CNC Spindle Motor 1 5KW Air cooled ER20 High Speed 18000rpm AC380V for Woodworking Lathe Machine
Click to see details
CNC Spindle Motor 1 5KW Air cooled ER20 High Speed 18000rpm AC380V for Woodworking Lathe Machine

CNC Spindle Motor 1.5KW Air-cooled ER20 High Speed 18000rpm AC380V for Woodworking Lathe Machine GDZ93*82-1.5

60 % of buyers enjoyed this product!
Availability: in stock
Price:  US $399.99 / piece
Sale Price:  US $359.99 / piece
get coupon
45 days Money back 45 days Money back Returns accepted if product not as described, buyer pays return shipping; or keep the product & agree refund with seller.
On-time Delivery On-time Delivery
Guarantees: On-time Delivery 60 days

Sort By

Top-rated Seller

Share:

18000rpm 1.5KW 380V CNC Spindle Motor ER20 Air-cooled Square 3.8A 300Hz 93*82mm 4 bearing High Speed for Woodworking

Providing the default Nut ER20 and Collet 6mm, if not please do contact us for a better solution.

Specification

Model

GDZ93*82-1.5-380V

Product type

Square High-Speed Motorized Spindle Motor for Aircooling for Woodworking

Speed (r/min)

18000

Power (KW)

1.5

Voltage(V)

380V

Current(A)

3.8A

Frequency (Hz)

300

Collect

ER20

Lubrication

Grease

Cooling type

Air cooling

Bearings

2×70005

2×7002

Warranty

Bearing for half a year, other parts for one year

Runout

0.01-0.02mm

Notice

Spindle motor must be inverter VFD output, cannot directly connect power supply

Dimension :

1. electric spindle practices

Electric spindle is a high-speed high-precision components rigidity, we must strictly follow the practices used spindle spindle motor, otherwise it will increase equipment failures, shorten equipment life. Please use the rule as follows:

(1) Before the boot, first ensure that the spindle cooling system to work properly, and then turn the power spindle. Do not use the spindle without the cooling conditions, it is necessary to check the fan and pump are working properly before use. If the spindle is water cooled, to check whether the cooling water containing impurities to ensure water is smooth.

(2) When using electric spindle, spindle from low according to the principle of high speed, gradually increasing speed to warm up, when the spindle load up to speed and smooth operation of the state after the required processing, can better protection spindle, to reduce the wear.

(3) during use is strictly prohibited beat, hit threaded spindle clamp and rotor end, so as not to reduce the component life, affect the results spindles used.

(4) During the operation, the tool must be replaced in the correct way. When the knife, the focus should be uniform, the tool should be aligned with the threaded end of the screw rotor, clamping can be. During operation the tool needs to be replaced before the replacement to wait Spindle cooling, avoid tool change at hot temperature state.

(5) During the operation, if the fixture card spindle rotor end, non-beat way to remove Jigs. Only under the premise of no damage to the rotor shaft threads with pliers and other tools to remove the chuck, and clean the rotor tapered bore and clamp the spindle to avoid Movies shorten life, affecting the quality of workpiece. If the fixture has completely lost precision, it must be replaced immediately.

2. The spindle maintenance specification:

(1) to control the spindle actual time worked. Theoretically prohibit spindle 24 hours of continuous work, operating 12 hours per spindle Spindle let rest at least 2 hours, in order to prevent the formation of shortened due to mechanical fatigue life of the spindle.

(2) to understand the conditions, the ambient temperature and the spindle temperature control. Spindle operating ambient temperature not higher than 35 centigrade degree, when the ambient temperature is above 35 centigrade degree should use air conditioners or other protective measures to reduce the room temperature, thereby reducing spindle temperature.

(3) The spindle cooling water must be kept clean and free of impurities, recommendations to clean up after the end of the spindle shaft waterway, scale and water holes to avoid clogging due to rust. Also, always pay attention to circulating water temperature in the tank, so the water temperature is too high, the cooling effect can not be achieved prefetching.

(4) Always check the power supply connector, to avoid damage to the connector loose or aging brings to the spindle and the drive.

(5) If the downtime to use again, you must tranches from low speed to high speed spindle run-in steps according to the spindle load running, in order to use in the run-through.

(6) during the loading and unloading cutter knife, must tool chuck nut clean.

3. Use Caution

(1) must match the drive spindle chosen correctly according to the electric spindle nameplate good debugging power, voltage and frequency.

(2) Set the frequency converter should be set command channel, and then set the display channel, and finally set the parameters. When setting parameters, be sure that the reference frequency, the frequency of the three highest rated frequency and consistency.

(3) The spindle is generally clockwise in the wrong direction, the drive can change settings or swap any two rotating wire the inverter output UVW terminal on.

(4) In general, water-cooled spindle surface temperature and ambient temperature greater than 20 degrees, the heat can be considered a spindle; when air-cooled spindle surface temperature greater than ambient temperature of 30 degrees, can be identified as the main heat seriously, immediately shut down cooling, a check

4. Maintenance Caution

(1) Spindle found abnormal sound, should immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.

(2) the operation of an abnormal burning smell, immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.

(3) If the spindle does not run the boot, do not start over, you should carefully check the following related matters: first check the drive parameters to determine the input and output voltage, the spindle parameter settings are correct. Second, check the power cord and wiring connector is plugged in and determine whether the contact connector problem.

(4) Since the electric spindle is a high speed, high rigidity precision components and must therefore be sent back to me by professionals or for repair.

We also supply other Air cooled Spindle Motor, just feel free to choose what you need.

Model Power Voltage Joint of Nose Current Frequency Speed Buy Now
GDZ93x82-1.5 1.5kw 220v ER20 6.8A 300Hz 18000rpm
GDZ93x82-1.5 1.5kw 380v ER20 3.8A 300Hz 18000rpm
GDZ93x82-2.2 2.2kw 220v ER25 10A 300Hz 18000rpm
GDZ93x82-2.2 2.2kw 380v ER25 5.5A 300Hz 18000rpm
GDZ93x82-3.5 3.5kw 220v ER25 15A 300Hz 18000rpm
GDZ93x82-3.5 3.5kw 380v ER25 8.8A 300Hz 18000rpm
GDZ120x103-4.5 4.5kw 380v ER32 9.5A 300Hz 18000rpm
GDZ120x103-6 6kw 380v ER32 12.6A 300Hz 18000rpm
GDZ120x103-7.5 7.5kw 380v ER32 15.5A 300Hz 18000rpm
GDZ170x150-12 12kw 380v ER40 16A 300Hz 18000rpm
GDZ65F-800 800kw 220v ER11 4A 400Hz 24000rpm
GDZ80-1.5F 1.5kw 220v ER11 5A 400Hz 24000rpm
GDZ80-2.2F 2.2kw 220v ER16 8A 400Hz 24000rpm
Average Star Rating:
0 out of 5 (0 Ratings)
Name Rating Feedback
Shipping Company Shipping Cost Estimated Delivery Time
DHL 3 - 7 days
UPS Expedited 3 - 7 days
EMS 5 - 14 days
Post Air Mail Free Shipping 15 - 45 days
Return Policy If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.

N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).

Most Popular from Category


Price:  US $399.99 / piece
Sale Price:  US $359.99 / piece
get coupon
24/7 Customer Service (800) 927-7671
We provide all of the tools of industrial needs of the lighter equipment and heavy equipment at a bargain price and competitive
Web
Analytics