Five-channel temperature reflow machine T-960W 4.5 KW 0-1500mm/min Single reflow soldering welding machine
Notice : if your place is remote ,then need to pay 35usd .
Heating Method:Infrared strengthen the system of hot air
Cooling zone number:1
PCB Max width:300MM
Conveyor direction:Left to right
Transport system:Network transmission and chain drive
Average Power:4.5 KW
warming up time:About 15 minutes
Temperature control range:At room temperature to 350 degrees
Temperature Control:PID closed-loop control
Temperature Accuracy:plus or minus1 degrees
PCB board Temperature distributed deviating :plus or minus 2 degrees
1.After startup Settings into the interface. Press F2 to curve selection, according to F1 point selection, press F3 / F4 set the corresponding zone temperature move up/down, press F5 to enter heating interface;
2.Five little red switch 1/2/3/4/5 each control on the temperature range of the first/on the temperature range of the temperature range of the first/second/third area/second temperature area;
3.Open the motor switch temperature balance, and adjust the belt speed;
4.Press F2 to stop heating, and enter the setting interface;
5.Each USES a temperature curve are as follows:
a.Curve 1, 2, suitable for welding of lead less solder; Such as: 85 sn/pb 15 70 sn/pb 30, etc.;
b.Curve of 3, 4, more suitable for welding of lead solder; Such as: 63 sn / 37 pb sn/pb 40 60, etc.;
c.Curve 5, 6, suitable for high melting point lead-free solder welding; Such as: Sn/Ag3.5; Sn/Cu. 75 Sn/Ag4.0 / Cu. 5 Sn95.5 Ag3.8 / Cu0.7, etc.;
d.Curve 7, 8, suitable for welding of lead-free solder melting point; Such as: Sn/Ag2.5 / Cu. 8 / Sb. 5. Sn/Bi3.0 Ag3.0, etc.;
e.Curve 1, 3, 5, 7 480 s recommended veneer welding cycle, curve 2, 4, 6, 8 280 s recommended veneer welding cycle.
1.When the welding chip, according to the requirements of the chip size and welding process, selection of an appropriate curve
2.Heating temperature, the distribution of the top three area, lower 2 area, corresponding to the heating curve of the first/second/third/fourth paragraphs / 5 paragraphs.
3.There are many kinds of, at present the production and use of solder each company chooses is not the same, the theoretical analysis and the analysis of the test article very much. For these reasons, the company launched the product can be preset eight curve, each a curve has five section, every period of heating time can change. Users can according to the heating temperature and the time required for solder from the new set the heating curve.
0 out of 5 (0 Ratings)
5 Stars (0)
4 Stars (0)
3 Stars (0)
2 Stars (0)
1 Star (0)
|Shipping Company||Shipping Cost||Estimated Delivery Time|
|3 - 7 days|
|3 - 7 days|
|5 - 14 days|
|Post Air Mail||Free Shipping||15 - 45 days|
|Return Policy||If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
|Seller Service||On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).|
Most Popular from Category
FTTH Splicing Welding Machine Signal Fire Ai-7 Intelligent Optical Fiber Cleaver Fusion Splicer
US $1349.99 / piece
Stud Welder Welding Machine STC-3150 220V Capacitor Discharge With Stud Torch Welding Range M3-M8
Aluminium Welding Machine TIG-250P AC DC welder, three phase AC380 50/60HZ tig welding machine
230V 1200W HDPE PVC Geomembrane Liner Wedge Welder Geomembrane Welding Machine LST-GM2
US $2678.00 / piece
WSE200 TIG-200 AC/DC tig welding machine,Aluminium Welding Machine
7 in 1 milti-function WELDING EQUIPMENT DC pulse 200AMP IGBT ARC/TIG ALUMINIUM Welding Equipment ALL ACCESSORIES
US $898.00 / piece
online shopping, buying directly from manufacturers?
- Go to Alibaba.com and enter the wanted item into search field.
- Having made your choice, click "Contact supplier" button on the right
- On the next page enter your request and click "Send" button.
- Upon clicking you will be asked to get registered. Do it and wait for the reply.